Printed circuit boards and their assemblies (PCB & PCBA) are the core components of electronic products, and their reliability directly determines the overall reliability of electronic products. To ensure and enhance the quality and reliability of electronic products, it is essential to carry out comprehensive physical and chemical analyses of failures, identify the underlying failure mechanisms, and then propose corresponding improvement measures. MTT possesses profound technical expertise in board-level failure analysis, a complete range of analytical methods, a vast database of case studies, and a team of experienced experts, providing you with high-quality and efficient failure analysis services.
The purpose of electronic component failure analysis is to employ a variety of testing and analytical techniques and procedures to identify the failure phenomena of electronic components, determine their failure modes and mechanisms, identify the ultimate root cause of failure, and propose recommendations for improvements in design and manufacturing processes. This helps prevent the recurrence of failures and improves the overall reliability of the components.
The continuous rise in complexity and performance requirements of integrated circuits, combined with potential risks across design, manufacturing, packaging, and application stages, has led to frequent occurrences of critical failure modes such as short circuits, open circuits, leakage, burnout, and parameter drift. These issues not only result in costly device scrapping and system downtime but also often trigger disputes over responsibility among designers, foundries, packaging and testing houses, and end-users, causing significant economic losses and reputational risks.
The performance requirements for polymer materials continue to rise, while differences in understanding of high-demand products and processes between customers and suppliers often lead to frequent failures such as fracture, cracking, corrosion, and discoloration. These failures frequently cause disputes over responsibility and result in significant economic losses.
The increasingly harsh service environments of metal components place higher demands on material performance and structural reliability. However, factors such as design flaws, material defects, manufacturing deviations, or improper use can readily trigger typical failures including fatigue fracture, stress corrosion cracking, hydrogen embrittlement, creep, wear, and overload deformation.
Didn't find what you were looking for?
Consult a professional engineer immediately for your service
Didn't find what you were looking for?
Consult a professional engineer immediately for your service
Meixin Testing leverages its technological edge in constructing massive failure databases, showcasing its capabilities through comprehensive case studies, solutions for complex scenarios, partnerships with leading enterprises, and systematic intellectual property. Drawing on millions of failure analyses, it delivers precise insights into root causes, enabling inspection reports to provide robust support for clients' quality upgrades and achieve zero failures.
Didn't find what you were looking for?
Consult a professional engineer immediately for your service
Stay updated with the latest news from Maxin Testing, including technical developments, exhibitions, and events. We build on a foundation of professional testing to deliver customized solutions for our clients, ensuring quality control from the source. This empowers our clients to stand out in the marketplace and achieve commercial success.
Didn't find what you were looking for?
Consult a professional engineer immediately for your service
MTT is a nationally accredited commercial third-party laboratory. We specialize in providing testing services, technical consulting services, and solution services to clients across industries including electronics manufacturing, automotive electronics, semiconductors, and aerospace materials.
Maxin Testing operates laboratory facilities in Shenzhen, Suzhou, and Beijing, featuring multidisciplinary testing and analytical laboratories. The company pioneers an industrial hospital service model grounded in materials science engineering and electronic reliability engineering.
Didn't find what you were looking for?
Consult a professional engineer immediately for your service
Professional verification platform, delivering precise data insights to build a solid foundation of trust for investors.
Didn't find what you were looking for?
Consult a professional engineer immediately for your service

How to Pinpoint PCB Leakage? Electrical Localization and Cross-Section Evidence of CAF

Release date: 2026-11-19 15:58
Share to:

PCB leakage is easy to confirm but hard to locate. Resistance between two pins tells you leakage exists, yet the conductive path may be buried inside the laminate where visual inspection and surface analysis cannot reach.

A power supply board developed leakage in the field, initially confirmed between pin1 and pin2 of a small-board connector. A normal board of the same model powered at 220 VAC produced normal output; the failed board entered protection mode after about 5 minutes under a 35 A load, with no output voltage. After the housing was opened, obvious water marks were visible on the surface of the failed board. The leakage location had to be locked down electrically first; once surface checks came back clean, the search moved inside the laminate.

1. Visual Inspection: Water Marks on the Housing

Method: The housings of the NG and OK samples were opened and examined under a stereo microscope.

Findings: Obvious water marks were present on the NG housing surface; no other visible anomaly was found.

Conclusion: The water marks are traces of a damp heat environment. Nothing on the surface directly explains the leakage, so the anomaly had to be sought further inside.

2. Electrical Analysis: Confirming Leakage Between Pin1 and Pin2

Method: Both boards were powered at 220 VAC and the voltages between connector pins were measured. The copper traces connecting pin1 and pin2 to the small board were then cut, 11.5 V was applied between pin1 and GND alone, and the voltage between pin1 and pin2 was measured again.

Findings:

  • The OK sample produced output voltage.
  • The NG sample entered protection mode after about 5 minutes under a 35 A load, with no output voltage. At that point the voltage between pin1 and pin5 was 0.697 V, and between pin2 and pin5 was 0.174 V. The protection mode corresponds to the condition where the pin2 voltage exceeds 3.5 V.
  • With the traces cut and power applied separately, 0.1742 V was measured between pin1 and pin2.

Conclusion: The leakage occurs between pin1 and pin2 and is unrelated to the front-end circuitry of the small board.

3. X-Ray Inspection: No Visible Anomaly Between the Through-Holes

Method: The pin1 and pin2 through-holes of the NG sample were examined by X-ray.

Findings: No obvious anomaly was found between the two through-holes.

Conclusion: X-ray projection cannot resolve finer internal defects, so the investigation continued.

4. Hotspot Localization: Hotspot Between the Two Through-Holes

Method: 11.5 V with a 5 mA current limit was applied to the pin1/pin2 circuit, and Thermal EMMI was used to collect the hotspot and locate the leakage.

Findings: The hotspot appeared between the pin1 and pin2 through-holes on the small board.

Conclusion: The leakage was localized between the two through-holes, confirming that current flows between pin1 and pin2.

5. Surface Analysis: No Anomalous Substance on the Through-Hole Surface

Method: After Pt sputter coating for 30 s, the morphology between pin1 and pin2 was examined by SEM/EDS and the composition measured. The surface solder flux and conformal coating were then removed and the area re-examined.

Findings: No obvious morphological anomaly or leakage-related substance was found between the leaking through-holes. After removing the solder flux and conformal coating, no anomalous substance appeared between the through-holes either.

Conclusion: Surface causes were ruled out. The leakage path is not on the surface, leaving only the laminate interior; the next step was cross-sectioning.

6. Cross-Section Analysis: Metal Filament and Cu Between the Through-Holes

Method: Samples were prepared by manual microsectioning per IPC-TM-650 2.1.1, ground down to the pin1/pin2 through-hole positions, and examined by metallurgical microscope and SEM with EDS composition measurement.

Findings:

  • An obvious metal filament connecting the two through-holes was present between pin1 and pin2.
  • A metal filament was also present between pin3 and pin4. Voids were found inside the glass fiber at the filament location, and EDS detected high Cu content there (17.1 wt% and 15.4 wt% at two positions), while no Cu was detected in the bulk substrate.

Conclusion: Conductive anodic filament (CAF) was present between both pairs of through-holes. The filament is extremely fine: the CAF between pin1 and pin2 was lost during grinding, while the one between pin3 and pin4 happened to be exposed on the polished plane.

Why X-Ray and SEM Showed No Anomaly

X-ray shows a projection image and SEM shows surface morphology; the CAF filament is hidden inside the glass-fiber gaps of the laminate, beyond the reach of both techniques. Electrical analysis, after cutting the copper traces connecting pin1 and pin2 to the small board and applying power separately, still measured 0.1742 V between pin1 and pin2, confirming the leakage was between those two pins. Hotspot localization then collected a hotspot between the two through-holes. Electrical methods locked down the position first, and cross-sectioning supplied the direct evidence of filament morphology and high Cu content.

Mechanism and Conclusion

Voids inside the glass fiber and resin gaps provide a migration path

↓

Under damp heat, copper dissolves anodically and ionizes

↓

The potential difference between pin1 and pin2 drives copper ion migration along the glass-fiber gaps

↓

Copper deposits in the path and grows into a metal filament connecting the two through-holes

↓

Resistance between the holes drops, leakage occurs, and the supply enters protection mode

The direct cause of the leakage on this power board is CAF between the pin1 and pin2 through-holes: the metal filament bridges the two holes, pulls the resistance down, and leakage follows. The filament between pin1 and pin2 was lost during grinding, so the direct morphological evidence comes from the CAF between pin3 and pin4 and the high Cu content in that region; electrical analysis and hotspot localization had already locked the leakage to pin1/pin2. The two lines of evidence support each other.

CAF formation requires four conditions: a potential difference provides the driving force for ion movement, a humid environment provides the medium for ionization, gaps inside the substrate such as resin and glass fiber provide the migration path, and metal ions provide the migrating species. Only when all four are met can a conductive filament grow. The water marks on the NG housing correspond to the humid-environment condition.

Disclaimer: This case has been desensitized. All data come from real laboratory analysis. Reproduction without permission is prohibited.

Relevant cases
Why Did the Hardness of a Zinc-Aluminum Alloy Drop After Aging? Missing Solution Treatment and Overaging
A zinc-aluminum alloy phone cover aged at 120–220°C for 12 h without solution treatment saw hardness fall from 147 HV to 89 HV. Hardness, composition, metallography, SEM/EDS, and heat-treatment verification showed the root cause was missing solution treatment and excessive aging parameters. The peak hardness window is solution treatment followed by 100°C×50 min.
Exporting to California? A Practical Guide to Proposition 65 and Its Litigation Traps
California Proposition 65 (Prop 65) is a state-level statute and is not limited by product category, covering the entire supply chain. Its regulated substance list contains more than 960 chemicals known to cause cancer or reproductive toxicity, yet only about 300 have official safe-harbor thresholds. This article explains its scope, the exemption boundaries, and the two compliance routes for businesses.
Still failing despite meeting IPC standards? The OSP film thickness tolerance vulnerability overlooked by 90% of factories
After undergoing two reflow temperatures, OSP pads exhibited severe solderability issues during wave soldering. Reducing the reflow temperature resolved the solderability problems. This paper analyzes the failure causes and mechanisms of solderability defects on OSP pads and proposes improvement recommendations.
The Truth Behind the 30% Surge in FPC Lead-Free Failure Rates | The “Invisible Killer” of Consumer Electronics
A certain FPC exhibited routing shallowing at certain locations, with both the edges and central areas of the defective samples showing this phenomenon. This paper will conduct a systematic failure analysis to identify the root cause of routing shallowing in the FPC.
Silicone Exceeding Limits = EU Sales Ban? With Global Regulations Tightening, Is Your Product Compliant?
Siloxanes are a class of organosilicon compounds containing Si-O-Si bonds, widely used in rubber, detergents, polishes, adhesives, sealants, and other fields. Due to the environmental and health risks associated with certain siloxanes, numerous countries and regions worldwide have enacted regulations to control their use.
Save Millions! Practical Tips for Avoiding Pitfalls in Metal Material Selection (Part 2)
In the previous article, “Choosing the Wrong Metal = Burning Money! A Guide to Avoiding Pitfalls in Metal Material Selection for Electronics (Part 1),” we established a knowledge framework for metal material properties and applications, and outlined the core steps for scientific material selection. However, theory must be tested by practice. This article will focus on the practical aspects: How can advanced inspection technologies provide reliable data support for material selection decisions? How can performance and cost be skillfully balanced in projects? Real-world case studies will reveal the consequences of improper material selection and the solutions to address them.
Email
marketing@mttlab.com
Business Consultation
Free Consultation
Report Inquiry
Back to Top
Contact Us
  • *Name:
  • *Contact:
  • *Email:
  • *Company/Organization/school:
  • *The location:
  • *Message information: